font test
Visitez notre section de produits en promotions pour des rabais importants!
- |
- Nouveaux produits
- |
- Aubaines
- |
- Catalogue
- en
BESOIN D'AIDE?
OUEST : 800 303-5222
EST : 800 361-2568
-
Produits
- Produits Ordinateur
- Mémoire Flash & SSD
- Électronique
- Audio / Vidéo
- Produits DEL
- Accessoires
-
Chargeurs / Batteries
Chargeurs / Batteries
- Adaptateur d'auto
- Batterie d'usage général
- Bloc pile portable
- Barre d'alimentation
- Batteries rechargeables et chargeur
- Adaptateur CA (remplacement)
- Batterie de remplacement
- Adaptateur CA (universel)
- Chargeur USB pour voiture
- Chargeur USB maison
- Chargeurs USB-C (Tablette/Portable)
- Recharge sans-fil (Qi)
- Produits Promotionel
- Sélection GAMERS
- Liquidation
- Logiciels
- Marques
- Récupération des données
- Mes services
- Configurateurs
- Promotions
- Accueil>
- Catalogue>
- Produits Ordinateur>
- Mémoire SODIMM>
- DDR3 - SODIMM>
- 8Go 1600MHz DDR3 Non-ECC CL11 SODIMM
8Go 1600MHz DDR3 Non-ECC CL11 SODIMM
Code de produit : 008027 (KVR16S11/8)
Code UPC : 740617207019
This document describes ValueRAM's 1G x 64-bit (8GB) DDR3- 1600 CL11 SDRAM (Synchronous DRAM) 2Rx8, memory module, based on sixteen 512M x 8-bit FBGA components. The
SPD is programmed to JEDEC standard latency DDR3-1600 timing of 11-11-11 at 1.5V. This 204-pin SODIMM uses gold contact fingers. JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
VDDQ = 1.5V (1.425V ~ 1.575V)
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address "000" only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
PCB : Height 1.180" (30.00mm), double sided component
SPD is programmed to JEDEC standard latency DDR3-1600 timing of 11-11-11 at 1.5V. This 204-pin SODIMM uses gold contact fingers. JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
VDDQ = 1.5V (1.425V ~ 1.575V)
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address "000" only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
PCB : Height 1.180" (30.00mm), double sided component